Solar UPS

Features

Advance MICRO CONTROLLER based SOLAR UPS / INVERTER products have been carefully designed to operate in both industrial and commercial environments. In commercial applications, our ups / inverter products fit according to aesthetically into the environment and perform reliably for years.

SALIENT FEATURES

• Built-in MPPT / PWM Solar Charge Controller.
• Micro Controller / DSP Based smart controller design.
• Pure Sine Wave Output.
• Electronic Overload and Short Circuit Protection.
• Easily Serviceable.
• Auto Changeover / Reset Feature.
• Mains Input Voltage Range Selection.
• Multi Stage Charging.
• Audio Visual Indications (Status & Fault).

User Manuals:

Specifications

Solar UPS: SO312

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO312
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	1
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	22VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	300
Output Watt Capacity (watts)	240W
DC System Voltage (VDC)	12V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	1
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO612

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO612
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	1
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	22VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	600
Output Watt Capacity (watts)	480W
DC System Voltage (VDC)	12V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	1
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO812

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO812
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	1
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	22VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	800
Output Watt Capacity (watts)	640W
DC System Voltage (VDC)	12V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	1
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO1024

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO1024
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	2
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	44VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	1000
Output Watt Capacity (watts)	800W
DC System Voltage (VDC)	24V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	2
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO10096

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO10096
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	8
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	176VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	10000
Output Watt Capacity (watts)	8000W
DC System Voltage (VDC)	96V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	8
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg :VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO10120

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO10120
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC, 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	10
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	220VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	10000
Output Watt Capacity (watts)	8000W
DC System Voltage (VDC)	120V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	10
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg :VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO10192

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO10192
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	16
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	352VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	10000
Output Watt Capacity (watts)	8000W
DC System Voltage (VDC)	192V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	16
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg :VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO15096

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO15096
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC, 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	8
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	176VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	15000
Output Watt Capacity (watts)	12000W
DC System Voltage (VDC)	96V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	8
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg :VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO15120

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO15120
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	10
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	220VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	15000
Output Watt Capacity (watts)	12000W
DC System Voltage (VDC)	120V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	10
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg :VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO15192

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO15192
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	16
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	352VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	15000
Output Watt Capacity (watts)	12000W
DC System Voltage (VDC)	192V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	16
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg :VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO1524

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO1524
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	2
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	44VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	1500
Output Watt Capacity (watts)	1200W
DC System Voltage (VDC)	24V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	2
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS » SO1536 Solar UPS: SO1536

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO1536
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC, 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	3
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	66VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	1500
Output Watt Capacity (watts)	1200W
DC System Voltage (VDC)	36V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	3
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO1548

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO1548
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	4
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	88VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	1500
Output Watt Capacity (watts)	1200W
DC System Voltage (VDC)	48V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	4
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO20096

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO20096
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	8
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	176VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	20000
Output Watt Capacity (watts)	16000W
DC System Voltage (VDC)	96V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	8
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg :VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO20120

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO20120
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC, 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	10
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	220VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	20000
Output Watt Capacity (watts)	16000W
DC System Voltage (VDC)	120V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	>300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	10
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg :VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO20192

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO20192
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC, 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	16
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	352VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	20000
Output Watt Capacity (watts)	16000W
DC System Voltage (VDC)	192V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	16
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg :VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO2036

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO2036
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	3
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	66VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	2000
Output Watt Capacity (watts)	1600W
DC System Voltage (VDC)	36V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	3
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO2048

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO2048
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC, 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	4
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	88VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	2000
Output Watt Capacity (watts)	1600W
DC System Voltage (VDC)	48V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	4
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO2072

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO2072
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	6
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	132VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	2000
Output Watt Capacity (watts)	1600W
DC System Voltage (VDC)	72V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	6
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO2548

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO2548
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	4
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	88VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	2500
Output Watt Capacity (watts)	2000W
DC System Voltage (VDC)	48V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	4
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO2572

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO2572
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	6
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	132VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	2500
Output Watt Capacity (watts)	2000W
DC System Voltage (VDC)	72V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	6
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO3048

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO3048
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	4
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	88VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	3000
Output Watt Capacity (watts)	2400W
DC System Voltage (VDC)	48V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	4
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO3072

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO3072
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	6
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	132VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	3000
Output Watt Capacity (watts)	2400W
DC System Voltage (VDC)	72V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	6
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO3096

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO3096
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	8
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	176VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	3000
Output Watt Capacity (watts)	2400W
DC System Voltage (VDC)	96V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	8
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO3548

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO3548
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	4
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	88VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	3500
Output Watt Capacity (watts)	2800W
DC System Voltage (VDC)	48V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	4
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO3572

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO3572
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	6
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	132VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	3500
Output Watt Capacity (watts)	2800W
DC System Voltage (VDC)	72V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	6
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO3596

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO3596
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	8
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	176VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	3500
Output Watt Capacity (watts)	2800W
DC System Voltage (VDC)	96V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	8
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO4072

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO4072
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	6
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	132VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	4000
Output Watt Capacity (watts)	3200W
DC System Voltage (VDC)	72V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	6
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO4096

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO4096
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	8
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	176VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	4000
Output Watt Capacity (watts)	3200W
DC System Voltage (VDC)	96V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	8
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO5036

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO5036
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	3
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	66VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	5000
Output Watt Capacity (watts)	4000W
DC System Voltage (VDC)	36V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	3
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO5048

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO5048
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	4
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	88VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	5000
Output Watt Capacity (watts)	4000W
DC System Voltage (VDC)	48V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	4
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO5096

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO5096
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	8
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	176VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	5000
Output Watt Capacity (watts)	4000W
DC System Voltage (VDC)	96V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	8
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg : VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO5120

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO5120
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	10
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	220VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	5000
Output Watt Capacity (watts)	4000W
DC System Voltage (VDC)	120V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	10
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg :VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO5144

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO5144
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	12
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	264VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	5000
Output Watt Capacity (watts)	4000W
DC System Voltage (VDC)	144V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	12
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg :VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO5192

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO5192
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	16
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	352VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	5000
Output Watt Capacity (watts)	4000W
DC System Voltage (VDC)	192V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	16
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg :VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO6144

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO6144
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC, 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	12
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	264VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	6000
Output Watt Capacity (watts)	4800W
DC System Voltage (VDC)	144V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	12
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg :VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO6192

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO6192
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC, 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	16
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	352VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	6000
Output Watt Capacity (watts)	4800W
DC System Voltage (VDC)	192V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	16
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg :VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO7.5192

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO7.5192
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	16
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	352VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	7500
Output Watt Capacity (watts)	6000W
DC System Voltage (VDC)	192V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	16
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg :VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.

Solar UPS: SO7.5144

Type	MPPT SOLAR CHARGE CONTROLLER
Model	SO7.5144
INPUT
Input Voltage Range	100V ~ 300V (Wide input voltage range)
	180V ~ 260V (Normal input voltage range)
Nominal Input Voltage(s) Supported	220V AC , 50Hz
Input connection type	Hard Wire
BATTERY Full Load Runtime (minutes)	Depends on Load & Battery AH
No of Battery	12
Solar Charge Controller
Type	MPPT/PWM
Max.PV Open Circuit Array Volatge	264VDC
Charge Algorithm	3-stage Bulk / Acceptance / Float Plus Equalize
LCD Display	Backlit, Alphanumeric Display showing battery voltage, DC amperage, Cumulative KW hours
OUTPUT
Output Volt Amp Capacity (VA)	7500
Output Watt Capacity (watts)	6000W
DC System Voltage (VDC)	144V
Load Capacity	>110% faulty after 300ms
Phases	1Phase – 3 Wire (L.N.E)
Output AC waveform	Pure Sine Wave
Efficiency	> 88%
GENERAL
LCD / LEDs Indications	UPS ON (Yellow), Battery Low (Red), Mains ON (Green),Charging (Green), Overload(Red)
Alarms	Audible alarm indicates power failure and overload conditions
Switches	1)Switch control off / on power status
	2)Switch for mains input voltage range
	3)Switch to select the maximum charging voltage
Protection	> 300% Load (with manual reset function)
Cooling Method	Forced air cooled
Transfer Time	Battery to line mode : 300 milliseconds / Line to battery mode : 300 milliseconds
Housing Material	Powder coated / painted MS
ENVIRONMENTAL
Operating Temperature Range	0°C to 50°C
Relative Humidity	95% (non-condensing)
Degree of Protection	IP 20
BATTERY
No of Battery	12
Battery Charging Profile(Boost /Foat)	Suitable according to Battery type (eg :VRLA/SMF/Wet Lead Acid Battery)
Max Charging Current(when battery is fully discharge)	10A ±2amp
SPECIAL FEATURES
Cold Start (startup in battery mode during a power failure)	Cold-start operation supported
Charge End Voltage	Grid charging stop when battery reaches 13.8V ±0.2V and transfer to backup mode (per battery)
Grid Recharge Voltage	Grid charging starts when battery reaches 11V ±0.2V and transfer to grid (per battery)
CERTIFICATIONS
Quality Certifications	ISO 9001:2008
WARRANTY
Product Warranty Period	1 – year limited warranty
Since we are committed to continuous development of our products, the specification are subject to change without notice.